[PATCH 12/25] docs/zh_CN: Add gadget_printer.rst translation

Patch content 1 changed file

Translate .../usb/gadget_printer.rst into Chinese. Update the translation through commit 570eb861243c("docs: usb: replace some characters") Signed-off-by: macrofun <baikefan@leap-io-kernel.com>--- .../translations/zh_CN/usb/gadget_printer.rst | 535 ++++++++++++++++++ 1 file changed, 535 insertions(+) create mode 100644 Documentation/translations/zh_CN/usb/gadget_printer.rst diff --git a/Documentation/translations/zh_CN/usb/gadget_printer.rst b/Documentation/translations/zh_CN/usb/gadget_printer.rstnew file mode 100644index 000000000000..c4bbbb013d2d--- /dev/null+++ b/Documentation/translations/zh_CN/usb/gadget_printer.rst@@ -0,0 +1,535 @@+.. SPDX-License-Identifier: GPL-2.0+.. include:: ../disclaimer-zh_CN.rst++:Original: Documentation/usb/gadget_printer.rst+:翻译:++ 白钶凡 Kefan Bai <baikefan@leap-io-kernel.com>++:校译:++++============================+Linux USB 打印机 Gadget 驱动+============================++2007年06月04日++版权所有 (C) 2007 Craig W. Nadler <craig@nadler.us>++++概述+====++该驱动可用于在 Linux 嵌入式系统中开发打印机固件。+请注意，它与在 Linux 主机上使用打印机无关。++你需要一个 USB 设备控制器以及其对应的 Linux 驱动，+该驱动支持使用 Linux USB Gadget API 的 gadget / 设备类驱动。+加载 USB 设备控制器驱动后，再加载打印机 gadget 驱动。+这样，连接到 USB 设备端口的主机将看到一个打印机接口。++该驱动针对运行在用户态的打印机固件设计。+用户态固件通过设备文件与内核态打印机 gadget 驱动读写数据。+当 USB 主机发送获取打印机状态的请求时，打印机会返回状态字节。+用户态固件可以通过设备文件 /dev/g_printer 读取或写入该状态字节。+支持阻塞和非阻塞的读/写操作。+++++使用方法+========++要加载 USB 设备控制器驱动和打印机 gadget 驱动。+以下示例使用 Netchip 2280 USB 设备控制器驱动::++	modprobe net2280+	modprobe g_printer+++加载打印机 gadget 时，可指定以下命令行参数+（例如：modprobe g_printer idVendor=0x0525 idProduct=0xa4a8）：++idVendor+    设备描述符中的厂商 ID。默认值为 Netchip 的 0x0525。+    发布产品前必须更改为自己的厂商 ID。+    如果需要申请厂商 ID，请参考 www.usb.org++idProduct+    设备描述符中的产品 ID。默认值为 0xa4a8。+    建议更改为其他未使用的 ID，产品编号可从 0x0001 开始。++bcdDevice+	产品版本号，建议填写固件版本。++iManufacturer+	厂商名称字符串。++iProduct+	产品名称字符串。++iSerialNum+	序列号字符串，每个产品单元应不同。++iPNPstring+	打印机使用的 PNP ID 字符串，可在命令行指定或硬编码。++qlen+	每个端点使用的 8k 缓冲区数量。默认值为 10，+	你应该根据你的产品进行调整。你也可能想调整+	每个缓冲区的大小以适应你的产品。+++++示例代码使用+============++该示例代码将打印机数据发送到标准输出，而不是打印机引擎。++要编译下面的测试代码：++1) 将其保存为名为 prn_example.c 的文件+2) 使用以下命令编译代码::++	 gcc prn_example.c -o prn_example++++从主机读取打印机数据到 stdout::++	# prn_example -read_data+++将打印机数据从文件 (data_file) 写入主机::++	# cat data_file | prn_example -write_data+++要获取 gadget 驱动的当前打印机状态::++	# prn_example -get_status++	Printer status is:+	     Printer is NOT Selected+	     Paper is Out+	     Printer OK+++设置打印机为选中/在线::++	# prn_example -selected+++设置打印机为未选中/离线::++	# prn_example -not_selected+++设置纸张状态为缺纸::++	# prn_example -paper_out++	# prn_example -paper_out+++设置纸张状态为有纸::++	# prn_example -paper_loaded++	# prn_example -paper_loaded+++设置错误状态为打印机正常::++	# prn_example -no_error+++设置错误状态为错误::++	# prn_example -error++	# prn_example -no_error+++要设置错误状态为错误::++	# prn_example -error+++++示例代码+========++::+++  #include <stdio.h>+  #include <stdlib.h>+  #include <fcntl.h>+  #include <linux/poll.h>+  #include <sys/ioctl.h>+  #include <linux/usb/g_printer.h>++  #define PRINTER_FILE			"/dev/g_printer"+  #define BUF_SIZE			512+++  /*+   * 'usage()' - Show program usage.+   */++  static void+  usage(const char *option)		/* I - Option string or NULL */+  {+	if (option) {+		fprintf(stderr,"prn_example: Unknown option \"%s\"!\n",+				option);+	}++	fputs("\n", stderr);+	fputs("Usage: prn_example -[options]\n", stderr);+	fputs("Options:\n", stderr);+	fputs("\n", stderr);+	fputs("-get_status    Get the current printer status.\n", stderr);+	fputs("-selected      Set the selected status to selected.\n", stderr);+	fputs("-not_selected  Set the selected status to NOT selected.\n",+			stderr);+	fputs("-error         Set the error status to error.\n", stderr);+	fputs("-no_error      Set the error status to NO error.\n", stderr);+	fputs("-paper_out     Set the paper status to paper out.\n", stderr);+	fputs("-paper_loaded  Set the paper status to paper loaded.\n",+			stderr);+	fputs("-read_data     Read printer data from driver.\n", stderr);+	fputs("-write_data    Write printer sata to driver.\n", stderr);+	fputs("-NB_read_data  (Non-Blocking) Read printer data from driver.\n",+			stderr);+	fputs("\n\n", stderr);++	exit(1);+  }+++  static int+  read_printer_data()+  {+	struct pollfd	fd[1];++	/* Open device file for printer gadget. */+	fd[0].fd = open(PRINTER_FILE, O_RDWR);+	if (fd[0].fd < 0) {+		printf("Error %d opening %s\n", fd[0].fd, PRINTER_FILE);+		close(fd[0].fd);+		return(-1);+	}++	fd[0].events = POLLIN | POLLRDNORM;++	while (1) {+		static char buf[BUF_SIZE];+		int bytes_read;+		int retval;++		/* Wait for up to 1 second for data. */+		retval = poll(fd, 1, 1000);++		if (retval && (fd[0].revents & POLLRDNORM)) {++			/* Read data from printer gadget driver. */+			bytes_read = read(fd[0].fd, buf, BUF_SIZE);++			if (bytes_read < 0) {+				printf("Error %d reading from %s\n",+						fd[0].fd, PRINTER_FILE);+				close(fd[0].fd);+				return(-1);+			} else if (bytes_read > 0) {+				/* Write data to standard OUTPUT (stdout). */+				fwrite(buf, 1, bytes_read, stdout);+				fflush(stdout);+			}++		}++	}++	/* Close the device file. */+	close(fd[0].fd);++	return 0;+  }+++  static int+  write_printer_data()+  {+	struct pollfd	fd[1];++	/* Open device file for printer gadget. */+	fd[0].fd = open (PRINTER_FILE, O_RDWR);+	if (fd[0].fd < 0) {+		printf("Error %d opening %s\n", fd[0].fd, PRINTER_FILE);+		close(fd[0].fd);+		return(-1);+	}++	fd[0].events = POLLOUT | POLLWRNORM;++	while (1) {+		int retval;+		static char buf[BUF_SIZE];+		/* Read data from standard INPUT (stdin). */+		int bytes_read = fread(buf, 1, BUF_SIZE, stdin);++		if (!bytes_read) {+			break;+		}++		while (bytes_read) {++			/* Wait for up to 1 second to sent data. */+			retval = poll(fd, 1, 1000);++			/* Write data to printer gadget driver. */+			if (retval && (fd[0].revents & POLLWRNORM)) {+				retval = write(fd[0].fd, buf, bytes_read);+				if (retval < 0) {+					printf("Error %d writing to %s\n",+							fd[0].fd,+							PRINTER_FILE);+					close(fd[0].fd);+					return(-1);+				} else {+					bytes_read -= retval;+				}++			}++		}++	}++	/* Wait until the data has been sent. */+	fsync(fd[0].fd);++	/* Close the device file. */+	close(fd[0].fd);++	return 0;+  }+++  static int+  read_NB_printer_data()+  {+	int		fd;+	static char	buf[BUF_SIZE];+	int		bytes_read;++	/* Open device file for printer gadget. */+	fd = open(PRINTER_FILE, O_RDWR|O_NONBLOCK);+	if (fd < 0) {+		printf("Error %d opening %s\n", fd, PRINTER_FILE);+		close(fd);+		return(-1);+	}++	while (1) {+		/* Read data from printer gadget driver. */+		bytes_read = read(fd, buf, BUF_SIZE);+		if (bytes_read <= 0) {+			break;+		}++		/* Write data to standard OUTPUT (stdout). */+		fwrite(buf, 1, bytes_read, stdout);+		fflush(stdout);+	}++	/* Close the device file. */+	close(fd);++	return 0;+  }+++  static int+  get_printer_status()+  {+	int	retval;+	int	fd;++	/* Open device file for printer gadget. */+	fd = open(PRINTER_FILE, O_RDWR);+	if (fd < 0) {+		printf("Error %d opening %s\n", fd, PRINTER_FILE);+		close(fd);+		return(-1);+	}++	/* Make the IOCTL call. */+	retval = ioctl(fd, GADGET_GET_PRINTER_STATUS);+	if (retval < 0) {+		fprintf(stderr, "ERROR: Failed to set printer status\n");+		return(-1);+	}++	/* Close the device file. */+	close(fd);++	return(retval);+  }+++  static int+  set_printer_status(unsigned char buf, int clear_printer_status_bit)+  {+	int	retval;+	int	fd;++	retval = get_printer_status();+	if (retval < 0) {+		fprintf(stderr, "ERROR: Failed to get printer status\n");+		return(-1);+	}++	/* Open device file for printer gadget. */+	fd = open(PRINTER_FILE, O_RDWR);++	if (fd < 0) {+		printf("Error %d opening %s\n", fd, PRINTER_FILE);+		close(fd);+		return(-1);+	}++	if (clear_printer_status_bit) {+		retval &= ~buf;+	} else {+		retval |= buf;+	}++	/* Make the IOCTL call. */+	if (ioctl(fd, GADGET_SET_PRINTER_STATUS, (unsigned char)retval)) {+		fprintf(stderr, "ERROR: Failed to set printer status\n");+		return(-1);+	}++	/* Close the device file. */+	close(fd);++	return 0;+  }+++  static int+  display_printer_status()+  {+	char	printer_status;++	printer_status = get_printer_status();+	if (printer_status < 0) {+		fprintf(stderr, "ERROR: Failed to get printer status\n");+		return(-1);+	}++	printf("Printer status is:\n");+	if (printer_status & PRINTER_SELECTED) {+		printf("     Printer is Selected\n");+	} else {+		printf("     Printer is NOT Selected\n");+	}+	if (printer_status & PRINTER_PAPER_EMPTY) {+		printf("     Paper is Out\n");+	} else {+		printf("     Paper is Loaded\n");+	}+	if (printer_status & PRINTER_NOT_ERROR) {+		printf("     Printer OK\n");+	} else {+		printf("     Printer ERROR\n");+	}++	return(0);+  }+++  int+  main(int  argc, char *argv[])+  {+	int	i;		/* Looping var */+	int	retval = 0;++	/* No Args */+	if (argc == 1) {+		usage(0);+		exit(0);+	}++	for (i = 1; i < argc && !retval; i ++) {++		if (argv[i][0] != '-') {+			continue;+		}++		if (!strcmp(argv[i], "-get_status")) {+			if (display_printer_status()) {+				retval = 1;+			}++		} else if (!strcmp(argv[i], "-paper_loaded")) {+			if (set_printer_status(PRINTER_PAPER_EMPTY, 1)) {+				retval = 1;+			}++		} else if (!strcmp(argv[i], "-paper_out")) {+			if (set_printer_status(PRINTER_PAPER_EMPTY, 0)) {+				retval = 1;+			}++		} else if (!strcmp(argv[i], "-selected")) {+			if (set_printer_status(PRINTER_SELECTED, 0)) {+				retval = 1;+			}++		} else if (!strcmp(argv[i], "-not_selected")) {+			if (set_printer_status(PRINTER_SELECTED, 1)) {+				retval = 1;+			}++		} else if (!strcmp(argv[i], "-error")) {+			if (set_printer_status(PRINTER_NOT_ERROR, 1)) {+				retval = 1;+			}++		} else if (!strcmp(argv[i], "-no_error")) {+			if (set_printer_status(PRINTER_NOT_ERROR, 0)) {+				retval = 1;+			}++		} else if (!strcmp(argv[i], "-read_data")) {+			if (read_printer_data()) {+				retval = 1;+			}++		} else if (!strcmp(argv[i], "-write_data")) {+			if (write_printer_data()) {+				retval = 1;+			}++		} else if (!strcmp(argv[i], "-NB_read_data")) {+			if (read_NB_printer_data()) {+				retval = 1;+			}++		} else {+			usage(argv[i]);+			retval = 1;+		}+	}++	exit(retval);+  }--2.34.1